Updated Nov 17, 2026· 7 min read

Key takeaways

  • Accuracy. Stages states plus or minus 1.5 percent of measured power.
  • Battery. One CR2032 coin cell per sensor, user-replaceable. Stages product pages list more than 175 hours for the dual-sided meter, and some retailers and reviewers quote higher figures. Listings differ, so treat the figure as a rough guide and plan to carry a spare cell.
  • Weight. The maker lists roughly 15 g added per sensor pod, so a dual-sided set adds about 30 g; some retailers quote up to 35 g for the pair.
  • Power range. The maker’s spec pages list 0 to 2500 W, although one independent review quotes 0 to 5000 W. For most riders neither limit matters, but the difference shows why you should read the spec page for your exact model.
  • Cadence. 10 to 220 rpm, from an accelerometer, so no magnet is needed.
  • Water resistance. IPX7.
  • Wireless. ANT+ and Bluetooth LE.
  • Operating temperature. -18 to 50 degrees Celsius.

A Stages dual-sided power meter is a Stages Cycling “Power LR” crankset or crank-arm system with strain sensors on both the left and right sides, and the buyer’s first decision is the bike: the maker’s Shimano catalog lists its dual-sided meters on Shimano cranksets, with Dura-Ace R9200 and Ultegra R8100 for road bikes and XTR M9220, XT M8200 and XT M8120 for mountain bikes. This is a cycling product, not an electrical tester, so the question is which crankset your drivetrain accepts and whether independent left and right readings are worth the extra cost over a single-sided meter.

What “dual-sided” means

A single-sided power meter measures one leg, normally the left, and doubles the number to estimate total power. That works well for riders whose legs are balanced. A dual-sided meter measures both legs independently, so it reports true left and right figures and a balance percentage, and it does not assume the two legs are equal. Riders recovering from injury, riders with a known imbalance and coaches who analyse pedal technique are the usual buyers.

Stages markets these as “Power LR”. Stages says each meter is individually calibrated, and lists active temperature compensation as standard on its meters.

Current dual-sided options

Stages’s Shimano catalog lists several dual-sided options; the pages reviewed here show no dual-sided Stages models for SRAM or Campagnolo. The table below summarises the models that appear on the maker’s pages.

Model Best for Stated details Limits
Stages Power LR Shimano Dura-Ace R9200 Road riders on 12-speed Dura-Ace-class drivetrains Built on the Shimano R9200 crankset; Stages describes a new design for this model Premium tier; fits R9200 geometry only
Stages Power LR Shimano Ultegra R8100 Road riders who want a Shimano 12-speed crankset with power Sensors on drive and non-drive sides; arm lengths and chainring combinations as the maker lists Chainring choices are limited to the offered combinations
Stages Power LR Shimano Ultegra R8000 Riders on an 11-speed Shimano road bike Dual-sided meter on the earlier R8000 crankset; availability varies, so confirm on the maker’s site Older drivetrain generation; check that your bike is 11-speed
Stages Power LR Shimano XTR M9220 Mountain bike riders on 12-speed XTR Dual-sided crankset power meter Premium tier
Stages Power LR Shimano XT M8200 Mountain bike riders on 12-speed XT Dual-sided crankset power meter Check chainring and chainline needs for your frame
Stages Power LR XT M8120 Mountain bike riders on an earlier XT drivetrain Earlier-generation XT crankset; check the maker’s page for chainring and arm options Availability dates vary by option on the page

Listings change as Shimano generations roll over, so always open the exact product page for your crankset before you order.

Specs Stages lists for the Power LR family

  • Accuracy. Stages states plus or minus 1.5 percent of measured power.
  • Battery. One CR2032 coin cell per sensor, user-replaceable. Stages product pages list more than 175 hours for the dual-sided meter, and some retailers and reviewers quote higher figures. Listings differ, so treat the figure as a rough guide and plan to carry a spare cell.
  • Weight. The maker lists roughly 15 g added per sensor pod, so a dual-sided set adds about 30 g; some retailers quote up to 35 g for the pair.
  • Power range. The maker’s spec pages list 0 to 2500 W, although one independent review quotes 0 to 5000 W. For most riders neither limit matters, but the difference shows why you should read the spec page for your exact model.
  • Cadence. 10 to 220 rpm, from an accelerometer, so no magnet is needed.
  • Water resistance. IPX7.
  • Wireless. ANT+ and Bluetooth LE.
  • Operating temperature. -18 to 50 degrees Celsius.

Compatibility and fit notes

Crankset matching

Stages builds the sensor into the actual crank arm, so you are buying a crankset, not a clip-on part. You need the correct generation (R8000, R8100, R9200, M8120, M8200, M9220), arm length and chainring combination. A bike with a different crank standard needs a different product.

Bottom bracket and frame

Shimano cranksets use specific spindle and bottom bracket standards. Check that your frame’s bottom bracket shell and your existing bearings suit the crankset the maker lists. If you are not sure, a bike shop can confirm fit, and a shop can also install the crankset using the torque values in Shimano and Stages documentation.

Factory install options

Stages lists factory-install services for some dual-sided models, where you send in your own crankset and the maker fits the sensors. Read the service page for what is accepted and the turnaround.

Head units and apps

The meters broadcast ANT+ and Bluetooth LE, so most cycling computers and training apps can read them. Left/right balance display depends on the head unit, so check its manual if balance is a priority.

Single-sided or dual-sided?

Question Single-sided leaning Dual-sided leaning
Do I want independent left and right data? No Yes
Am I recovering from an injury or aware of an imbalance? No Yes
Do I want to minimise weight and cost? Yes Less important
Do I want the longest battery life? Yes (right-side units are listed with longer life) Listed at more than 175 hours
Do I swap between bikes? Possibly easier on single-sided crank-arm options Crankset must move or be duplicated

Budget, mid-range and premium tiers

  • Mid-range: Ultegra R8000 and XT M8200-class models are the more affordable ends of the dual-sided range because the underlying cranksets are less costly.
  • Premium: Dura-Ace R9200 and XTR M9220 sit at the top because they build on the maker’s top-tier cranksets, and they cost more than the Ultegra and XT versions.
  • Budget: dual-sided Stages meters are rarely in the budget tier. If cost is the main limit, a single-sided meter is the usual way to get power data.

Pick-by-need decision table

Pick this if you … Look at
Ride a 12-speed Shimano road bike and want the top-tier crankset Dura-Ace R9200 Power LR
Ride a 12-speed Shimano road bike and want a lower tier Ultegra R8100 Power LR
Ride an 11-speed Shimano road bike Ultegra R8000 Power LR, if it is still offered for your size
Ride a 12-speed XTR mountain bike XTR M9220 Power LR
Ride a 12-speed XT mountain bike XT M8200 Power LR

Alternatives

  • Single-sided Stages meters. Stages sells a left-arm meter on Shimano cranks, such as the Power L for Shimano 105 R7000. It gives total power by doubling the left leg.
  • Pedal-based dual meters. These measure both legs and move between bikes more easily, but they are a different product family from other brands, so compare their own manuals.
  • Spider or hub-based meters. These measure total power and do not report left and right independently.

Ownership notes

  • Do a zero-offset (calibration) before rides, as the manual describes, with the crank hanging free and the bike unweighted.
  • Replace coin cells before a long event; a flat cell stops transmission.
  • Do not pressure-wash the sensor area, even with IPX7 protection, and follow the user guide’s cleaning instructions.
  • If the crank is dropped or crash-damaged, stop using it and have it inspected, since a damaged crank arm is a mechanical safety issue.

Practical buying checklist

  1. Confirm the crankset generation on your bike: Shimano R8000, R8100, R9200, M8120, M8200 or M9220 each need their own Stages product.
  2. Confirm arm length and chainring combination. The maker’s Ultegra R8100 page lists arm lengths and chainring combinations to choose from; mountain bike pages list their own chainring sizes.
  3. Check that your cycling computer or app reads ANT+ or Bluetooth LE power data, and whether it shows left and right values.
  4. Plan a spare CR2032 cell for each sensor, since battery life in the maker’s pages is stated in hours, not months.
  5. Decide whether you want a shop to fit the crankset. Shimano cranksets rely on correct torque and bottom bracket condition, which a mechanic can confirm.

Stages also explains that its meters broadcast power and cadence from the crank, so a separate cadence sensor is not needed. If your head unit is old, read its manual before assuming it supports dual-sided data.

Frequently Asked Questions

Is Stages dual-sided available for SRAM or Campagnolo?

The maker’s pages reviewed here show dual-sided models on Shimano cranksets only. Stages sells other power meter options for other brands, so check the maker’s full product listing for your drivetrain.

How accurate is a Stages dual-sided meter?

Stages states plus or minus 1.5 percent of measured power for its meters, with individual calibration and temperature compensation. Actual results depend on correct installation and zeroing.

How long do the batteries last?

Stages product pages list more than 175 hours for the dual-sided meter, and some reviewers and retailers quote more than 200 hours, with less when optional features are enabled. Because listings differ, assume the lowest figure when planning battery changes.

Can I swap the crankset between bikes?

Yes, if both bikes share the same bottom bracket standard and drivetrain compatibility, though the swap takes tools and care. Many riders find it simpler to use one meter on one bike.

Do I need to buy a new crankset?

For most Power LR models, yes, because the meter is built into a complete crankset. Some factory-install services let you send your own crankset; read the specific page for requirements.

What does left/right balance tell me?

It shows the share of total power each leg produces. A small difference is normal, and a persistent large difference is a reason to talk to a coach or healthcare professional if you have discomfort, rather than something to correct on your own.

A
admin
We compare specs, materials and verified owner reviews before a product earns a spot. Rankings are never paid.
Affiliate disclosure. As an Amazon Associate we earn from qualifying purchases at no extra cost to you. Prices accurate as of the date shown.